Accessibility Links
  • Job reference: RMS0156745

NDT Inspector

  • Sector: Oil & Gas
  • Location: Geoje
  • Job type: Contract
  • Date posted: 07/05/2015
  • Time left:
    d h m s
This vacancy has now expired.
The Role:
The job holder is responsible to :
 Support and enforce the HSEQ Project objectives and directives. Also support and implement the Project
HSEQ Management System (plans, procedures and specifications).
 Directly report to the Lead Structure and Piping Inspector for the Structural and Piping matters and to
Welding/NDT Lead for the welding and NDT matters.
 Ensure the compliance of the fabrication and construction works with the engineering.
 Ensure the compliance with applicable codes for Structure, Piping and NDT code, specifications and
standards and best shipbuilding practices for offshore platforms.
 Ensure the responsibility of monitoring the construction of the FPSO structure and piping (ship part,
offshore areas, steel outfitting…) including living quarters when required.
 Cross-check by UT each Structure Special categories and review RT film for Piping and structure.
 Review Inspection and Test Plans to verify that Contractor is performing all required NDT inspections and
witnessing. Mark up NDT Inspection and Test plans with witness and hold points for NDT Inspection.
 Monitor the contractors NDT control system implementation, throughout the project performance, in
accordance with the approved ITP, procedures and NDT drawings and contractor data base.
 Monitor any Contractor’s staff or processes qualifications (NDT operator, welding welders, PWHT, etc…)
 Supervise the activities of Contractor’s NDT inspectors (welding, NDT,…)
 Ensure the monitoring of Contractor’s tracking registers (qualifications, certifications, calibrations etc.
follow-up) and required data bases (piping access data base, material traceability data base etc…)
 Check and follow, in liaison with the QC coordinators, the Sub-Contractor/Contractor’s NCR, and
Company C.A.R. status and relevant correctives action if required.
 Make sure that the impact of Sub-contractors or Contractor acceptable Deviation Requests on the ongoing
quality performance have been properly implemented and reflected in the As Built documentation
and monitor randomly the step by step compilation of executive documentation (final dossier) in
contractor or sub contractor’s premises.
 Participate in the welding and metallurgy discussion/supervision and welding book review.
 Review Inspectors deliverables, analyze and resolve issues and problems emerging during the NDT
control activity.
 Attend to weekly welding/NDT meetings with Contractor to review NDT work progress, quality
issues/failures, NCR etc.
 Review of QC data base as routine activities, ensure the review and completion of all the welding and
NDT for the structure at block final, pre-erection and dock erection stage respectively.
 Review of QC data base as routine activities. Ensure the review and completion of all the welding and
NDT for the piping at spool release at pre-fabrication shop, flushing or pressure test respectively.
 Perform any other tasks as assigned by hierarchy.
 Ensure that an effective implementation of HSE system is applied, as appropriate at site.
 Take time for checking safety documents and permits at site.
 Ensure that risk assessment prior to start new activity is properly conducted and understood by
personnel involved.
 Make himself visible at site and available/approachable for discussion about HSE concerns.

 Certificates in QC (Welding/NDT…others)
 Minimum 10 years experience in NDT/Welding role in Petrochemical, Refinery or Fabrication Yard, of
which 5+ years shall have covered most aspects of fabrication.
 Experience with piping and /or structure
 Knowledge of all applicable standard (GS EP STR, BV, IACS, DNV, ASME and AWS)
 Knowledge of quality process
 Communication and reporting skills
 Familiar with the Yard practices (Construction drawing, shop drawing NDE map and weld map)
 Visual, MPT, UT, RT certified base on EN473 for structure or SNT-TC-1A for piping
 CWI (Certified Welding Inspector) base on DWS and CSWIP on EN Standard
 Language: Fluent English, Korean
Similar jobs
Eric Armin
Procurement Quality Coordinator Location: Houston, Texas Duration: 12 months The Role: Responsible to implement Project Quality Plan in...